Length: 13m28cm
Width: 243cm
Height: 305cm (discharge down)
Chipping Capacity: 66cm diameter (26”)
Opening: 66cm high x 68cm wide (26”x27”)
Chassis Frame: 28cm x 11.4cm x 0.95cm Wall Tube with two (2) 11.4cm reinforcement plate – total 28cm x 10cm. With 10cm x 10cm and 10cm x 20cm tube cross-members – equals total 10cm x 25cm tube with 1.27cm top and 1.27cm bottom reinforcement 11.4cm wide
Diesel Engines: 700 to 1,500hp by various Manufacturers as options available on request.
Axle: Minimum two (2) 9,070kg
Brakes: Air Brakes
Battery Box: 10 Gauge steel construction; lockable, and welded to the frame; primed and painted for rust protection.
Tires: Four (4) 425/65 R22.5; 57cm x 31cm rims
Tow Bar: Fifth Wheel Style for Semi Tractor
Fuel Tank: Minimum1,758 liter
Lighting: 24 Volt system and conform to DOT standards; taillights shall be a sealed system, shock mounted to frame with grommets. Break and turn lights shall be located at the rear sides of the infeed chute and flush mounted within a welded steel housing for protection. All wiring shall be protected within a non-corrosive abrasion resistant, shielded loom.
Jack: Two (2) hydraulic operated, 23cm x 28cm tube with 46cm x 46cm footpads.
Paint: All exposed areas shall be covered with industrial strength primer and then shall be painted with industrial strength, lead free, urethane paint for enhanced rust protection. Standard color shall be industrial yellow, DuPont Imron
Chipper Shaft: 15cm diameter x 238cm long in 15cm w x 63.5cm pillow block bearing.
Feed Plate Anvil: Steel construction, custom fitted, adjustable with 2 usable edges.
Chipper Cutting Drum: Discone style; 8 pocket, 76cm wide with 1.27cm thick skin; 119cm diameter large end tapered to 71cm diameter small end.
Disc: 2.5cm x 180cm Disc diameter
Chipper knives: 8 knife pockets; each with one (1) 19.05cm L x 14cm x 1.59cm, 2 edge reversible.
Chipper Housing: 1.9cm plate.
Discharge: Hydraulic Operated with directional chip deflector, with replaceable wear plates; 270 degree swivel
Capacity: Minimum chipper throat opening 68cm high by 66cm wide with a total cutting width of 70cm; shall have a minimum of 0.48 sq. meter feed opening area.
Feed Rate: 33 meters per minute unless otherwise specified, with variable speed capability.
Hydraulic Tank: Minimum of 945 liter capacity.
Hydraulic Hose: All high pressure hydraulic hoses shall be minimum 175kg/sq. cm industrial grade construction with wear and spray guards in applicable areas; shall have female JIC 37° flare fittings.
Filtration System
Feed System: Top (Horizontal) 91cm diameter x 60cm wide with sharp teeth, internal hydraulic drive; two(2) 38cm diameter x 78cm Long vertical positioned 10cm apart on center, 7cm shafts and 152cm wide from outside to outside of feedwheels.
In-feed Bed: 472cm long x 244cm wide with 10cm x 20cm tube substructure. With adjustable two(2) strand WD-110 Drag Chain.
Drum Bearings: Chipper bearings shall be 10cm spherical, high speed; 8 bolt ISAF pillow block housing rated at: dynamic 18,820kg; radial 2,260kg with 10,000 hour service life.
Chipper Drive: Drive belt shall be three (3) 5 band
Controls: Fully integrated CAN BUS system that monitors all critical hydraulic and engine function; allows “on-the-fly” engine settings changes: includes three(3) MODE operating system to match process choice.
Shields All shields shall be constructed of steel and positioned to form a complete housing covering all moving parts including drive belts and chipper housing to insure operator safety, protect machine from fallen material, suppress dust, and dampen noise; shields shall be securely fastened to the machine and totally bolted together using grade 8 bolts.
